Documentation
Getting Started
Installation and Access
Network Configuration
Verification and Maintenance
Frequently Asked Questions (FAQ)
Search this page by keyword. One question per entry, no long articles.
Each entry gives the conclusion and a pointer; follow the link for detailed steps.
Sign-in and admin page
The browser cannot open 192.168.10.1. What should I do?
First check that the address includes https://, then check that the computer is on 192.168.10.x.
Detailed steps: Cannot open the admin page
I get "Your connection is not private". Has the device been infected?
No. The device uses a self-signed certificate.
Click Advanced → Proceed.
Detailed steps: Cannot open the admin page
What are the default account and password for the gateway?
Account root, password admin.
Change the password immediately after signing in.
Detailed steps: Signing in to the gateway
I forgot the gateway password. What can I do?
You can only restore factory settings and configure the device again; the existing configuration is erased.
Detailed steps: Device maintenance
I changed the configuration but the page does not respond?
Changes take effect only after you click Apply Configuration.
Wait a few seconds, then refresh the page to confirm.
Internet access and wiring
The gateway has no internet after configuration. What do I check first?
Check whether the WAN port protocol matches the access mode you chose.
Detailed steps: Sign-in and internet access
In secondary router mode, which subnet should the LAN port use?
It must not share a subnet with the upstream optical modem.
If the modem is 192.168.1.x, use 192.168.2.1 for the gateway LAN.
Detailed steps: Secondary router mode
Should DHCP be turned off in bypass router mode?
Yes.
Otherwise it competes with the upstream router to hand out addresses, which shows up on site as random disconnects.
Detailed steps: Bypass router mode
The bypass router is configured, but remote devices are still unreachable. Why?
You also need to point the terminal gateway to the gateway LAN port.
Alternatively, add a static route on the upstream router.
Detailed steps: Bypass router mode
Should the optical modem be switched to bridge mode?
Switch it if you can. Bridge mode is the most stable and gives the highest success rate.
If you cannot change it, use secondary router or bypass router mode.
Detailed steps: Choosing an access mode
Which of the three access modes should I choose?
If you can change the optical modem and have the broadband account, choose bridge.
If the modem cannot be changed, choose secondary router.
If the existing network structure must not be touched, choose bypass router.
Detailed steps: Choosing an access mode
Platform and networking
The gateway has internet access, but the platform does not show the device?
Check three things: whether EasyTier is enabled, whether the start method is web configuration, and whether the account name exactly matches the platform account.
Detailed steps: Networking and reachability
What happens if the case of the account name in the platform address is wrong?
The device will not come online.
It must match the account registered on the platform exactly.
Detailed steps: Networking and reachability
The device is added on the platform, but the two sides still cannot ping each other?
Nine times out of ten the subnet proxy is not configured, or the two sites use the same subnet.
Detailed steps: Configuring subnet proxies
Can every site use 192.168.1.x?
No. Each site must use a different subnet.
Otherwise the tunnel comes up, but the sites cannot reach each other.
Detailed steps: Preparation
What CIDR should I enter for the subnet proxy?
Enter only the local site's LAN subnet, for example 192.168.2.0/24.
Do not enter the peer site's subnet, and do not enter 0.0.0.0/0.
Detailed steps: Configuring subnet proxies
Which access control options should I enable?
Both directions: virtual network → LAN, and LAN → virtual network.
Detailed steps: Access control
Does a new store need the whole configuration again?
Yes. Add the new site to the network with the same procedure and configure its own subnet proxy.
Detailed steps: Adding the gateway to a network
Speed and services
Ping works, but web pages or the surveillance system do not open?
Ping only proves layer-3 connectivity.
First confirm that the remote service is running and that the local firewall allows it.
Detailed steps: Verifying site-to-site connectivity
The surveillance feed stutters and speed is slow?
First check whether the store's uplink bandwidth is insufficient.
Then enable latency priority, QUIC proxy, and KCP proxy.
Detailed steps: Slow network and stuttering surveillance
Does turning on every optimization switch make it faster?
Not necessarily.
Change one item at a time and observe for 10 to 30 minutes before deciding.
Detailed steps: Network optimization
How many sites can one network hold?
Pending (to be filled in by the content provider).
Is a public IP address required?
Pending (to be filled in by the content provider).
Go to the Troubleshooting overview and look up the symptom.
Next → Troubleshooting overview
Was this page helpful?A one-line note helps us make these steps more accurate.